Drilling & Injecting

Drilling concrete slabs and injecting chemical is one of the ways to protect a property from termites, and then there are obviously variations of those treatment methods depending on the type of construction and requirements of the treatment. However, there have to be a few specifications met to ensure it is done correctly. Here we will highlight a few for you to consider.

Hole Spacings! When holes are drilled to inject termiticide under a concrete slab to treat the footing of a wall, the holes cannot be more than 150mm from the wall. This home had holes exceeding 300mm. Needless to say, the original treatment failed and the home was re infested. 

Injecting Termidor under a slab.

Holes are often drilled around a perimeter to ensure a complete chemical barrier to prevent termites getting in.

Hole spacings on this property exceeded 300mm! Once again, they were beyond specification, holes should be between 150-300mm apart. The greater tolerance is reserved for porous soil types and rarely used in our practice. Ironically this was done on an internal wall that was a 

Once again, hole spacing was beyond specification. More examples below.... 

Mould. A sure sign of high moisture.

High moisture is a major conducive condition to termite attack, and nothing says "hey there's lots of moisture here" better than fungus.  Mould is often seen growing in areas of persistent moisture. So it's not surprising that where here is mould, there are termites nearby. This is because the prevailing conditions required for both mould and termites are very similar. So if you see mould in your place, it might be time to get a termite inspection. It's also a good idea to do all you can to reduce the moisture (and mould!) in your home for health reasons. 

Mould on the side of this book highlights the persistent high humidity in this room. Not only bad for your health but is also a sign of high moisture. Forget book worms, it's book mould! 

A leaking bathroom provided all the moisture needed for this mould to grow nicely on a ceiling! 

High moisture , a warm environment and a cold aluminium window frame allows mould to grow as moisture condenses on the aluminium.

Termite Hazard map.

We often get asked if a particular suburb has ha high incidence of termite activity. I often have to explain that most areas are! If you look at this map you'll notice that a lot of the highly populated areas of Australia are also zones with high environmental termite pressure!

How to identify termite mudding.

We often get calls when people find some dust, debris or any fine material that appears out of places it probably shouldn't. Good news is, it's not always termites, but it's bad news when it is. How can you identify what it is?

Termites build mud shelter tubes to keep them nice and cozy and moist, they can't be exposed as they will dehydrate and die. So, keeping this in mind, you need to remember that you're looking for nice moist, tightly packed mud. If the termite activity isn't new, the mud may be quite dry and cracked, but it's normally quite dense and difficult to break off. Termites are great engineers, and they will build solid mud tubes that protect them from the outside world.

If you see any debris or something that isn't where it should be, give it a rub with your finger, if it's hard and doesn't break away easily then it could likely be termite mud!

Here are some pictorial examples of what to look for: 

The Termite mudding is clearly visible on this property on the Central Coast, that is, after you remove the paint!

Termite mud packed in between an engaged pier in a subfloor and a dwarf wall. The mud is packed in tightly and does not fall out easily!

This termite activity is quite obvious! However, subtle signs are also present. Notice the bubbling of the paint on the right hand side just below the mudding. This is a sign of significant activity jay below the surface, this is something we look for during inspections as well. This was on a property in Mangrove Mountain.

Termite mud packed in behind this architrave is a dead giveaway. Although it may seem really obvious, sometimes the orientation of the door makes it hard to look at the doorway side on.

Here is a deceptive example:

This appeared like evidence of termites at a distance initially, (it was  up on the top of a garage). Closer inspection revealed that it was just debris made up of dust, fluff and spiders webs. 

Arsenic Trioxide Dusting - A Dangerous way to kill termites!

This is some termite damaged timber that has been treated with Arsenic trioxide dust. You can see the remnants of the arsenic in the galleries in the timber, its bright red! Arsenic trioxide dust was introduced many years ago as a means of treating live termites in their workings in an attempt to eradicate the colony. Whilst it has been an effective means, arsenic trioxide is extremely toxic and there are much better methods nowadays that don't introduce toxic chemicals into your property. Termidor dust and baiting are just some methods that can be used. Unfortunately, arsenic trioxide is still readily available and still being used by pest controllers in Australia.